3D Hexa Poly Candle Mold: A Simple Guide to Casting Geometric Candles at Home

The Azlok 3D Hexa Poly Candle Mold is a transparent poly-acrylic mould that lets you cast a neat, six-sided decorative candle at home. You melt your wax, add a wick, pour into the mould, let it set, and pop out a finished hexagon candle roughly 4.5 cm wide and 7.5 cm tall. It is a beginner-friendly tool for anyone who wants clean geometric candles without buying expensive equipment.

What you can make with it

This mould is built for one job and does it well: producing a solid three-dimensional hexagonal candle with crisp edges. The finished candle weighs around 89 grams, which makes it a handy size for gifting, table centrepieces, or a small home fragrance project.

Decor candles for shelves, mantelpieces and festive tables.
Scented candles when you add fragrance or essential oils to the wax.
Coloured pillar candles using wax dye chips or blocks.
Small-batch gifts and hampers for Diwali, weddings and housewarmings.

How to use the 3D Hexa Poly Candle Mold

The method is straightforward once you have your basics ready. You will need candle wax (soy, paraffin or beeswax), a suitable wick, and optionally colour and fragrance.

Set the wick. Thread a pre-waxed wick through the mould's wick hole and secure it at the base. Keep it centred and taut across the top using a pencil or stick laid over the opening.
Melt the wax. Use a double boiler and heat the wax gently until fully liquid. Follow the temperature range recommended on your wax pack.
Add colour and scent. Stir in dye and, once slightly cooled, your fragrance or essential oil. Mix thoroughly but gently to avoid air bubbles.
Pour. Fill the mould slowly and steadily to reduce trapped air. Leave it undisturbed on a level surface.
Cool and set. Let the candle harden completely at room temperature. A dip in the centre near the wick is normal; you can top up with a little extra wax.
Demould. Once fully firm, flex the acrylic gently and ease the candle out. Trim the wick to about 1 cm before lighting.

Tips for a better finish

Pour at the temperature your wax recommends. Too hot can cause cracks; too cool can trap bubbles.
Chilling the mould briefly can help with clean release, but let poured wax cool naturally to avoid surface marks.
A light coat of mould-release spray or a wipe of oil can make demoulding easier for stubborn waxes.
For a glossy surface, pour on a warm day and let the candle cool slowly.
Always burn candles on a heat-safe surface, away from curtains and children, and never leave a lit candle unattended.

Buying and storage

You get one mould per pack, and it is made in India from sturdy poly-acrylic. The mould itself is light at around 57 grams but holds its shape well through repeated use. Store it clean and dry, away from direct heat and sharp objects that could scratch the transparent surface. To clean, wipe out residual wax while it is still slightly warm, then wash with mild soap and lukewarm water — avoid very hot water, which can warp acrylic. You can find this mould and other candle-making supplies on Azlok, which keeps the basics stocked for home makers and small businesses.

FAQ

What size candle does this mould make?

The mould measures 5.3 cm by 9.2 cm and produces a hexagonal candle of roughly 4.5 cm by 7.5 cm, weighing about 89 grams.

Which wax works best in it?

Soy, paraffin and beeswax all work. Soy wax is popular for beginners because it releases cleanly and burns evenly. Follow the melting and pouring temperatures printed on your wax pack.

Is the mould reusable?

Yes. The poly-acrylic construction is designed for repeated casting. Clean it after each use and store it away from heat to keep it in good shape for many batches.

Can I add fragrance or essential oils?

Yes. Add your fragrance oil or essential oil once the melted wax has cooled slightly, then stir well before pouring. Use candle-safe fragrance quantities as recommended for your wax type.

How do I remove the candle without breaking it?

Wait until the candle is fully set. Gently flex the acrylic mould and ease the candle out. A little mould-release spray or a light oil coating before pouring makes this easier.